Professional Installation & Rigging
Certified marine technicians for outboard, inboard, generator, and transmission installation across the Netherlands, Germany, Belgium, and beyond. We handle everything from engine mounting to full control rigging and sea trials.
🔧 Installation Services
Outboard Motor Installation
Complete mounting, rigging, and commissioning for all outboard brands and horsepower ranges.
- Transom inspection and reinforcement
- Engine mounting and torque to spec
- Remote control cable installation
- Hydraulic steering connection
- Power trim/tilt wiring
- Fuel line assembly and pressure test
- Battery, charging system, and ECU setup
- Propeller selection and pitch check
- Sea trial and performance tuning
Inboard Engine Repowering
Full diesel and gasoline inboard installation, from bed fabrication to shaft alignment.
- Engine bed design and fabrication
- Transmission mating and SAE alignment
- Propeller shaft alignment (dial indicator)
- Coupling and cutless bearing fitting
- Raw-water and closed cooling plumbing
- Wet exhaust system installation
- Fuel system (tank, filters, lines, pumps)
- Electrical (starter, alternator, gauges, ECU)
- Vibration analysis and engine mount tuning
Generator Installation
Marine and industrial genset installation with proper ventilation, exhaust, and load testing.
- Compartment ventilation calculation
- Engine bed and sound shield mounting
- Wet exhaust riser and hose routing
- Fuel supply and return line installation
- AC output panel and breaker integration
- Remote start/stop and monitoring panel
- Load bank testing and voltage verification
- 50 Hz / 60 Hz frequency calibration
Transmission & Gearbox
Transmission installation, torsional analysis, and control system setup.
- SAE flywheel housing compatibility check
- Crankshaft endplay measurement
- Input coupling and drive plate installation
- Torsional vibration analysis
- Shaft alignment (angular and parallel)
- Oil cooler and raw-water plumbing
- Mechanical / hydraulic / electronic control setup
- Gear shift and throttle synchronization
🎯 Rigging & Controls
Mechanical Cable Controls
Traditional push-pull cable systems for tiller and remote control setups. We measure, cut, and terminate cables to exact length for smooth, low-effort operation. Standard on outboards up to 150 HP and inboards with single helm stations.
Hydraulic Steering & Controls
Low-effort hydraulic steering for outboards and inboards. We install helm pumps, cylinders, hoses, and reservoirs with proper bleeding and pressure testing. Ideal for vessels over 25 feet or any boat requiring fingertip steering.
Electronic Controls (CANbus / NMEA 2000)
Digital throttle, shift, and joystick systems from ZF, Mercury, Yamaha, and Volvo Penta. We integrate with your existing MFD, autopilot, and GPS for single-lever, station-transfer, and trolling mode operation.
Instrumentation & Gauges
Installation of tachometers, oil pressure, coolant temperature, fuel level, trim position, and digital multifunction displays. We calibrate senders and verify accuracy against factory specifications.
📋 Our Installation Process
Site Survey
We inspect your vessel, measure clearances, and verify compatibility with your chosen engine or equipment.
Quotation
Detailed written quote including labour, materials, consumables, and estimated completion time.
Preparation
Engine beds fabricated, old equipment removed, and all systems drained and prepped for installation.
Installation
Engine mounted, systems connected, and all fasteners torqued to manufacturer specification.
Alignment & Testing
Shaft alignment verified, systems pressure-tested, and electrical diagnostics run.
Sea Trial
On-water testing including RPM range, temperature, oil pressure, and performance verification.
💶 Installation Pricing Guide
| Service | Starting From | Typical Duration | Notes |
|---|---|---|---|
| Outboard Installation (up to 30 HP) | €450 | 4–6 hours | Includes controls, fuel, electrics, sea trial |
| Outboard Installation (30–90 HP) | €750 | 6–10 hours | Hydraulic steering extra |
| Outboard Installation (90–300 HP) | €1,200 | 1–2 days | Includes dual station rigging if required |
| Inboard Repower (Diesel, single engine) | €3,500 | 3–5 days | Engine beds, alignment, exhaust, sea trial |
| Inboard Repower (Twin diesel) | €6,500 | 5–8 days | Includes shaft alignment and vibration check |
| Generator Installation (up to 15 kW) | €1,800 | 2–3 days | Ventilation, exhaust, AC panel, load test |
| Transmission Replacement | €1,500 | 2–3 days | Includes endplay measurement and alignment |
| Hydraulic Steering Install | €850 | 1 day | Helm pump, cylinder, hoses, bleeding |
| Electronic Controls Upgrade | €2,200 | 2–3 days | Single to dual station, NMEA 2000 integration |
| Shaft Alignment Service | €450 | 4–6 hours | Dial indicator, adjustment, report |
🛡️ Installation Warranty & Certification
12-Month Installation Warranty
All labour and workmanship is covered for 12 months from the date of sea trial. If an installation-related fault develops, we will rectify it at no charge, including travel within the Netherlands. This is in addition to the manufacturer's engine warranty.
Signed Installation Certificate
Upon completion, you receive a detailed installation certificate including engine serial numbers, torque specifications, alignment readings, oil and coolant types, and a signed sea trial report. Required by most insurers and essential for warranty claims.
🌍 Service Coverage
Our mobile installation teams are based in Nieuwersluis, Netherlands, and operate across the following regions:
🇳🇱 Netherlands
All provinces. No travel surcharge for installations within 50 km of Nieuwersluis.
🇩🇪 Germany
North Rhine-Westphalia, Lower Saxony, Hamburg, Bremen, Schleswig-Holstein. Travel surcharge applies.
🇧🇪 Belgium
Flanders and Brussels regions. Travel surcharge applies.
Ready to Book Your Installation?
Contact our installation team for a site survey and detailed quotation. We will inspect your vessel, confirm compatibility, and provide a fixed-price quote with no hidden costs.
Book Installation Request a Quote